Product TOP
A general-purpose model that supports a wide range of applications from judgmental use such as assembly verification to dimensional measurement.
It can be used for a wide range of applications while keeping costs low.
- Excellent resistance to workshop conditions : Equivalent to IP64 (P type)
- Measuring range : 12 mm, 32 mm
- Maximum resolution : 1 µm, 5 µm
- Accuracy : 6 µm p-p, 10 µm p-p (Depends on the measurement length and resolution.)
- Resistant to oil, water, dust, vibration, and shock.
- Supports Φ8 mm stem mounting and side mounting with M4 screws
- Tough against oil and dust
- Pneumatic push type is also available, in which the spindle is driven by air supply.
Specifications
Specifications | |||||
---|---|---|---|---|---|
*1 The mass indicated is the total mass excluding the cable. Magnescale reserves the right to change product specifications without prior notice. |
|||||
Model | DT12N | DT12P | |||
Spindle driving | Spring push (Pneumatic push is possible with accessory DZ176) | ||||
Measuring range | 12 mm | ||||
Maximum resolution | 5 µm | ||||
Measuring force (at 20 °C) | Upward | 0.7 ±0.5 N | 1.7 N or less | ||
Horizontal | 0.8 ±0.5 N | 1.7 N or less | |||
Downward | 0.9 ±0.5 N | 1.7 N or less | |||
Accuracy (at 20 °C) | 10 µm p-p | ||||
Operating temperature | 0 to +50 °C | ||||
Storage temperature | −10 to +60 °C | ||||
Output cable length | 2 m | ||||
Stem diameter | Φ8 0‒0.015mm | ||||
Feeler | Steel ball tip, Φ3 mm, M2.5p x0.45 screw | ||||
Mass*1 | Approx. 75 g | Approx. 80 g | |||
Protection grade | – | Equivalent to IP64 |
Specifications | |||||
---|---|---|---|---|---|
*1 The mass indicated is the total mass excluding the cable. *2 The measuring force is the value when the spigot is open at an input air pressure of 1.96×105 Pa. *3 The measurement force is the value when the spigot is open at an input air pressure of 2.35×105 Pa. Magnescale reserves the right to change product specifications without prior notice. |
|||||
Model | DT32N | DT32NV | DT32P | DT32PV | |
Spindle driving | Spring push | Pneumatic push | Spring push | Pneumatic push | |
Measuring range | 32 mm | ||||
Maximum resolution | 5 µm | ||||
Measuring force (at 20 °C) | Upward | 1.1 ±0.8 N *2 | 2.9 N or less | 9 N or less *3 | |
Horizontal | 1.3 ±0.8 N *2 | 2.9 N or less | 9 N or less *3 | ||
Downward | 1.5 ±0.8 N *2 | 2.9 N or less | 9 N or less *3 | ||
Accuracy (at 20 °C) | 10 µm | ||||
Operating temperature | 0 to +50 °C | ||||
Storage temperature | −10 to +60 °C | ||||
Output cable length | 2 m | ||||
Stem diameter | Φ8 0‒0.015mm | ||||
Feeler | Steel ball tip, Φ3 mm, M2.5p x0.45 screw | ||||
Mass*1 | Approx. 120 g | Approx. 140 g | Approx. 120 g | Approx. 140 g | |
Protection grade | – | – | Equivalent to IP64 | Equivalent to IP64 |
Specifications | |||||
---|---|---|---|---|---|
*1 When MT20 is connected Magnescale reserves the right to change product specifications without prior notice. |
|||||
Model | DT512N | DT512N-T10 | DT512P | DT512P-T10 | |
Spindle driving | Spring push (Pneumatic push is possible with accessory DZ176) | ||||
Measuring range | 12 mm | ||||
Maximum resolution | 1 µm | ||||
Measuring force (at 20 °C) | Upward | 0.7 ±0.5 N | 1.7 N or less | ||
Horizontal | 0.8 ±0.5 N | 1.7 N or less | |||
Downward | 0.9 ±0.5 N | 1.7 N or less | |||
ccuracy (at 20 °C) | 6 µm p-p | 3 µm p-p *1 | 6 µm p-p | 3 µm p-p *1 | |
Operating temperature | 0 to +50 °C | ||||
Storage temperature | −10 to +60 °C | ||||
Output cable length | 2 m | ||||
Stem diameter | Φ8 0‒0.015mm | ||||
Feeler | Steel ball tip, Φ3 mm, M2.5p x0.45 screw | ||||
Mass *2 | Approx. 75 g | Approx. 80 g | |||
Protection grade | ― | Equivalent to IP64 |
Accessory
DT12/32/512
Feeler
DZ-100 | Roller feeler | |
DZ-123 | Φ3 mm carbide ball tip feeler | |
DZ-191 | Coupling feeler | |
DZ-5100 | Feeler set (pin, off-center, carbide flat, plastic spherical) |
Lift lever
DZ-161 | Lift lever (To allow manual sliding, this is mounted between the spindle and the feeler.) |
Air lifter
DZ176 | Air lifter for DT12/512 |
Gauge stand
DZ-521 | Stand for gauge, mounting hole Φ8 |
Extension cable
CE08-1, 3, 5, 10, 15 | Extension cable for LT series / MG series (1, 3, 5, 10, 15 m) | |
CK-T12, 13, 14, 15, 16 | Flex-resistant extension cable for LT series / MG series (1, 3, 5, 10, 15 m) |
Interpolator
MT16-01, 05 | A/B quadrature, voltage-differential line driver output (resolution 1, 5 µm) | |
MT17-01, 05 | A/B quadrature, voltage-differential line driver output, bare wires (resolution 1, 5 µm) | |
MT20-01, 05 | For MF10 (resolution 1, 5 µm) | |
MT30-01, 05 | For USB output (resolution 1, 5 µm) |